Monocok 2.72

軟體性質: 免費試用 ‎檔案大小: 3.54 MB
‎使用者評分: 3.8/5 - ‎2 ‎評分

Monocok 設計用於製造具有卵巢形式的帆板或飛機的機身。 它還可用於設計簡單的直升機或船殼。 這是一個簡單的軟體,由模型製造商為模型製造商設計。 多虧了 Monocok,你夢寐以求的所有型號都變得容易實現! 單體可用於設計具有木單體結構的刻度模型或製造模具(聚苯乙烯或玻璃纖維)。 Monocok (新版本 2.72) 允許簡單地進行以下操作: * 直觀地設計機身,無特殊知識,以圓潤的形式。 * 一些修改的即時預覽 (樣本 - 平滑) * 數字值 + 和 [-] 的精確和動態調整按鈕。 * 用滑鼠直觀地修改配置檔表單。 * 載入每個檢視的背景圖像(範本)。 * 在半前部分添加居中凹口。 * 選擇性出口前者。 * 即時縮放至 0.5。 * 以前的號碼預覽 * 所有機身半前機的佈局和列印 * 有可能在前者上添加凹口。 * 三個模型配置檔的佈局:左右側輪廓以及頂部視圖。 * 精確安裝機身的形式和大小與控制前。 * 自動計算中間前數。 * 在多個頁面上設計計劃(A4 到 A0,B5 到 B0,C4 到 C0,美國格式)。 * 將計劃匯出為 PDF 格式進行列印。 * 將機身的前名和配置檔匯出為 DXF 格式。 * 保護所有項目參數。 * 即時預覽模型與抗鋸抗。 * 精度為 1/10 mm 的改裝。 * 公制(毫米)或英寸(英寸)的管理

版本歷史記錄

  • 版本 2.72 發佈於 2011-05-06
    新功能

軟體細節

終端使用者許可協定

Monocok user license and warranty limitations IMPORTANT : Carefully read the following license and warranty information. This license agreement is a legal agreement between you (either an individual or a single entity) and Sebastien D'heeger, the author of Monocok(the software). By installing or otherwise using this software you agree to be bound by this agreement. If you do not agree to the terms of this Agreement, you may not install or use this software. USING THE SOFTWARE INDICATES YOUR ACCEPTANCE OF THESE TERMS.The software is provided with RESTRICTED RIGHTS. All rights are reserved to Sebastien D'HEEGER. Term of License : This software is a shareware. This software can be sold only by the author himself. You can use or distribute freely the evaluation version (unregistered) of Monocok. You may not disassemble, modify or reverse engineer any part of this software. You must not rent or sell this software to anyone. Registration : You can use Monocok during 30 days with this evaluation version.To get the full version with unlimited use time, thank to register.The registration key is only for you. Any reproduction or transmission of the registered version, even partial, in some form that it is, is prohibited without express authorization written of the author M.Sebastien D'heeger. If you are a registered user, you are entitled to use this product for your own use. You may not sell or rent the software to others. You must not give away your personal registration key, and/or the registered version. Limited Warranty : The author of this software does not guarantee that this software is free from bugs.Users of this software must accept this disclaimer of warranty. This software and documentation are provided "AS IS". The author disclaims all warranties, expressed or implied, including, without limitation, the warranties of merchantability and of fitness for any purpose. The author assumes no liability for damages, direct or consequential,which may result from the use of this software. Informations : Questions and suggestions are welcome at: [email protected] Monocok (c) - 2011 Sebastien D'HEEGER - All rights reserved. Any reproduction or transmission of the full version, even partial, in some form that it is, is prohibited without express authorization written of the author M.Sebastien D'heeger.