本模組可用於 SKF 公司滾動軸承的選擇、計算和檢查。該方案為下列任務提供解決方案： - 選擇和檢查合適的軸承。該檔包括一個資料庫，約10，000個不同的滾動軸承SKF在所有的基本類型和設計。 - 計算基本軸承參數（壽命、靜態安全等）。 - 根據ISO 281的新方法計算調整后的軸承壽命。 - 使用一對錐形滾子軸承或一對角接觸滾珠軸承的負載計算。 - 支援 2D 和 3D CAD（AutoCAD、AutoCAD LT、IntelliCAD、灰石墨、TurboCAD、BricsCAD、ZWCAD、ProgeCAD、歐特克發明家、固體工程、固體時代、克里奧）。 除了上述基本計算外，該文檔還包括其他幾個輔助計算（例如，潤滑劑操作粘度的計算、可變負載所裝載軸承平均負載的計算、允許的軸承速度的計算等）。 本程式使用來自專業文獻、SKF、ISO、ANSI、SAE 標準和其他來源的數據、程式、演算法和其他資訊。 相關標準：ISO 15、ISO 76、ISO 104、ISO 281、ISO 355、ISO 1132、ISO 5593、 ISO 5753、ISO 3448、ISO 15312、DIN 61 DIN 620、DIN 625、DIN 628、DIN 630、DIN 635、DIN 711、DIN 715、DIN 720、DIN 722、DIN 728、BS 290、BS 292、BS 3134。 本模組是 MITCalc - 機械和技術計算包的一部分， 齒輪、皮帶和鏈條傳動裝置、軸承、彈簧、梁、軸、螺栓連接、軸連接、公差和許多 別人。
版本歷史記錄
- 版本 1.20 發佈於 2017-07-11
更新了SKF軸承資料庫 - 版本 1.18 發佈於 2014-08-26
軟體細節
終端使用者許可協定
LICENSE AGREEMENT Please carefully read the following license agreement. Installation of this software means that you accept all the below mentioned conditions. LICENSE: By purchasing this software you also obtain a non-transferable right from the producer for: - Installation and use of this software on a master computer and another backup computer (notebook, home computer) provided that the computer(s) on which the software is installed is your own or under your control. Only one user can work with this software at any one time. - Installation and use of this software within the prescribed period whilst you are obliged to stop using this software after expiration of the prescribed period. Any attempt to break the protection preventing use of the software after the prescribed period is considered a breach of this agreement and can also be considered a breach of the copyright. - Displaying results. In case your license has expired, you can see results of the calculations which were carried out before expiration of your subscription. TEST PERIOD - DEMO VERSION: As a user, you have the right to test this software for a period of 30 days after installation. Any other use of the software (including competition analysis) is not permitted within the test period. After expiration of this term, you must delete the installed software or purchase a license. EXTENSION, CORRECTIVE PATCHES, NEW VERSIONS: The producer may issue various extension modules, corrective patches or new versions. All these supplements are available by uploading from web pages of the producer (partners of the producer). These extension modules, corrective patches and new versions can be used only within a valid license. OWNERSHIP RIGHTS AND COPYRIGHTS: Ownership rights and copyrights to this software (including all illustrations and document) belong to the producer. ACTIONS WHICH ARE NOT PERMITTED: - Circumventing or deleting in any way protection of those parts of the software which are locked for displaying. - Circumventing or deleting in any way protection preventing unauthorized use of the software. - Copying and using the algorithms and procedures included in this software for the purpose of development of other software. - Any distribution of this software (or its parts) in return for payment. - Providing any information (particularly the Authorization Code) which could lead to unauthorized use of the software by a third party. ACTIONS WHICH ARE PERMITTED: - Changing and modifying those parts of the software which are specified in the documentation to the software. - Translating parts of the software into other languages for your own purposes only. LIABILITY FOR DAMAGE: This technical and engineering software is designed for professional workers. It cannot in any way replace expert opinions or material and safety tests. The producer is, therefore, not responsible for any direct and/or indirect damage caused by errors in the software or due to its incorrect use, even in cases where the producer or his contractual partners is warned that such damage may arise. The user agrees with this level of risks. GUARANTEES: The producer is not responsible for trouble-free operation of the software. The only chance of remedy is that the producer will try to correct any possible defects and resolve the problems at his discretion. Producer MITCalc - Ing. Miroslav Petele; Stolicni 1205/6; 405 01 Decin; Czech Republicwww.mitcalc.com; [email protected]; [email protected]